IOtech MultiScan 1200 Скачать руководство пользователя страница 147

Страница: 147 / 364

TempScan / MultiScan User's Manual

Chapter 9: TempView 137

Configure Meter Pop-Up Menu Items (Meters Only)

This menu is similar for all three Meters Windows.

Note: The Show & Reset Peak Hold Indicator items does not appear in the Digital Meters menu.

Configure Meter Pop-up Menu Items

(Click on right mouse button in Meters Channel Display)

Unlike the

TempView Charts Window

, each

TempView Meters Window

features a

Configure Meter

pop-up menu. Access this menu as follows:

If not already done so, open the desired

TempView Meters Window

Place the mouse cursor over the desired channel of the

Channel Display

area

(H)

Click on the right mouse button. A pop-up menu will appear. Note that the

TempView Digital

Meters Window

has no pull-down, toolbar, or pop-up menu items referring to Peak Hold.

Select Channel…

Selects an active channel for the desired meter display.

This dialog box is similar for all three Meters Windows.

TempView Meters Select Channel Dialog Box

(Pop-Up Menu > Select Channel…)

Содержание MultiScan 1200













































































































































































































































































































































































Результаты поиска

Содержание MultiScan 1200

Отзывы:

Бренды по названию

Популярные бренды

IOtech MultiScan 1200, Руководство пользователя

Результаты поиска

Содержание MultiScan 1200

Отзывы:

Бренды по названию

Популярные бренды