IOtech MultiScan 1200 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 364

IOtech MultiScan 1200 Скачать руководство пользователя страница 24

14 Chapter 2: TempScan/1100 & MultiScan/1200

TempScan / MultiScan User's Manual

TempScan/1100 & MultiScan/1200 Specifications

CAUTION

CAUTION

CAUTION

CAUTION

Please read this manual carefully! If equipment is used in any manner not
specified in this manual, the protection provided by the equipment may be
impaired.

Note:

These specifications are subject to change without notice.

Channels

Number of Slots:

One (1) slot

Number of Channels (TempScan/1100):

Up to 32 differential thermocouple or voltage inputs, or up

to 16 RTD inputs; accepts TempTC/32B, TempV/32B, or TempRTD/16B scanning modules

Number of Channels (MultiScan/1200):

Up to 24 differential thermocouple or voltage inputs;

accepts MTC/24 or MHV/24 scanning modules.

Channel Attributes:

High and low set points; hysteresis values for high and low set points.

Scan Sequence:

Any combination of temperature and voltage channels may be scanned, but channels

are scanned in ascending numerical order.

Scan Interval:

Absolute time between scans (

hh:mm:ss.s

); min = 00:00:00.0, max = 99:59:59.9.

Note that specifying a value of 00:00:00.0 results in no delay between channel scans.

Scanning Modes (TempScan/1100):

For thermocouples up to 500 feet:

960 channels/sec @ 60 Hz;

800 channels/sec @ 50 Hz;

For thermocouples over 500 feet:

240 channels/sec @ 60 Hz, 200

channels/sec @ 50 Hz.

Scanning Modes (MultiScan/1200):

For multi-channel scanning:

147 channels/sec @ 50 or 60 Hz;

For 32-point line-cycle averaging enabled:

44 channels/sec @ 60 Hz, 38.5 channels/sec @ 50 Hz;

For single-channel burst mode:

1 channel @ 20K samples/sec.

Triggers

Installation Category:

For CE:

Category 1.

Programmable Triggering:

Temperature or Voltage level (above or below), absolute time of day,

alarm condition (on or off), IEEE GET, IEEE TALK, external TTL trigger (rising or falling),
specified number of readings.

Temperature-Level Trigger:

Programmable value for any one channel.

For MultiScan/1200:

This

trigger not available when in single-channel burst mode.

TTL Trigger:

Programmable for rising or falling edges.

Pre-Trigger Count:

Programmable integer (< memory size -1).

Post-Trigger Count:

Programmable integer.

Trigger Input Connector:

External BNC connector

Trigger Output Connector:

External BNC connector

«
...
22
23
24
25
26
...
»

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды