IBM totalstorage 326 Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 240

background image

Table 21. Storage controller troubleshooting (continued)

Problem indicator

Component

Possible cause

Possible solutions

Intermittent or sporadic
power loss to the
storage controller

Some or all
CRUs

Defective AC power
source or partially
plugged-in power
cord

1. Check the AC power

source.

2. Reseat all installed

power cables and
power supplies.

3. If applicable, check

the power
components.

4. Replace defective

power cords.

Power supply has
failed

Check for a Fault LED
on the power supply, and
replace the failed CRU.

Midplane has failed

Have the midplane
replaced (service
technician only).

Unable to access
drives

Drives and Fibre
Channel loop

Fibre Channel
cabling has failed.

Ensure that the Fibre
Channel cables are
undamaged and properly
connected.

RAID controller has
failed

Replace the RAID
controller.

GBIC has failed

1. Ensure GBIC is

seated properly.

2. Replace GBIC.

Random errors

Subsystem

Midplane has failed

Have the midplane
replaced (service
technician only).

Replacing hot-swap drives

Drive problems include any malfunctions that delay, interrupt, or prevent successful
I/O activity between the hosts and the hard disk drives. This section explains how to
replace a failed drive.

Attention:

Failure to replace the drives might result in loss of data. If you are

replacing a drive that is part of a RAID level 1 or RAID level 5 logical drive, ensure
that you install the replacement drive in the correct bay.

Use the following procedure to replace host-swap drives:

1. Check the hardware and software documentation that is provided with the

system to see if there are restrictions regarding hard-disk-drive configurations.
Some system Fibre Channel configurations might not allow mixing different drive
capacities or types within an array.

2. Check the storage-management software for recovery procedures for a drive

that has failed. Follow the steps in the software procedure before continuing
with this procedure.

3. Determine the location of the drive to remove.

Attention:

Never hot-swap a drive CRU when its green Activity LED is

flashing. Hot-swap a drive CRU only when its amber drive-fault LED is on and
not flashing, or when the drive is inactive with the green Activity LED on and not
flashing.

116

Model 326 User’s Reference

«
...
126
127
128
129
130
...
»

Содержание totalstorage 326

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для totalstorage 326

Бренд: NavigateWorx Страницы: 71

Бренд: YASKAWA Страницы: 34

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: Pantech Страницы: 17

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

Бренд: 3Com Страницы: 18

Бренд: Supermicro Страницы: 24

Бренд: FONESTAR Страницы: 8

Бренд: JUMO Страницы: 60

RocketCache 3240X8

Бренд: HighPoint Страницы: 17

IPLink 2603 Series

Бренд: Patton Страницы: 120

ADSL2+ Wireless MIMO Router

Бренд: Ace Страницы: 64

BPTA-CPUMS-V2-SKA

Бренд: Bitspower Страницы: 6

Бренд: QTech Страницы: 406

Бренд: TP-Link Страницы: 2

802.11a/b/g SDIO WiFi Module SDM3100

Бренд: Abocom Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды