IBM totalstorage 326 Скачать руководство пользователя страница 127

Страница: 127 / 240

Table 21. Storage controller troubleshooting (continued)

Problem indicator

Component

Possible cause

Possible solutions

One or more green
LEDs off

Power supply
CRUs

Power cord
unplugged or
switches turned off

Make sure that the
power cord is plugged in
and the power-supply
switches are turned on.

All drive CRUs

Midplane failure

Have the midplane
replaced (service
technician only).

Front panel

Power supply
problem

Make sure that the cords
are plugged in and
power supplies are
turned on.

Hardware failure

If any other LEDs are on,
replace the midplane
(service technician only).

Battery

Battery failure

Replace the battery.

Cache active

The cache is
disabled, the cache
has failed, battery
failure

1. Use the

storage-management
software to enable
the cache.

2. Replace the RAID

controller.

3. Replace the battery.

Host loop

Host, managed hub,
or switch is off or
has failed

1. Check if host

managed hub or
switch is on.

2. Replace attached

devices that have
failed.

Fibre Channel cable
has failed

Ensure that the Fibre
Channel cables are
undamaged and properly
connected.

GBIC has failed

1. Ensure GBIC is

seated properly.

2. Replace GBIC.

RAID controller has
no power or has
failed

1. Ensure that the unit

is powered on.

2. Replace RAID

controller.

Expansion loop

Drives are
improperly installed
or not installed

Ensure that the drives
are properly installed.

RAID controller has
no power or has
failed

1. Ensure that the unit

is powered on.

2. Replace the RAID

controller.

3542 drive failure

Replace the drive.

Externally attached
expansion port
device has failed

1. Replace the drive.
2. Replace the

expansion unit GBIC
or Fibre Channel
cable.

Chapter 8. Troubleshooting

115

Содержание totalstorage 326

















































































































































































































































Результаты поиска

Содержание totalstorage 326

Отзывы:

Похожие инструкции для totalstorage 326

Бренды по названию

Популярные бренды

IBM totalstorage 326, Справочник пользователя

Результаты поиска

Содержание totalstorage 326

Отзывы:

Похожие инструкции для totalstorage 326

Бренды по названию

Популярные бренды