IBM totalstorage 326 Скачать руководство пользователя страница 112

Страница: 112 / 240

Troubleshooting the Gigabit Ethernet SX adapter

Use Table 13 to find solutions to GB Ethernet adapter problems that have definite
symptoms.

See “Testing the Ethernet adapters with Intel PROSet II” on page 99 for information
on testing the adapter.

Table 13. Gigabit Ethernet SX adapter troubleshooting chart

Gigabit adapter symptom

Suggested Action

No Link or TX/RX Activity

If you cannot link to your switch, check the following:

1. Check the following LED lights on the adapter:

TX — On

The adapter is sending data

RX — On

The adapter is receiving data.

Link — On

The adapter is connected to a valid link partner and is receiving link
pulses.

Link — Off

Link is inoperative.

a. Check all connections at the adapter and link partner

b. Make sure the link partner is set to 1000 Mbps and full-duplex

c. Ensure the required drivers are loaded

PRO — Programmable LED

Identifies the adapter by blinking. Use the Identify Adapter push-button in
INTEL PROSet II to control blinking.

2. Ensure that the cable is installed correctly. The network cable must be securely

attached at all connections. If the cable is attached but the problem persists, try a
different cable.

Your computer cannot find
the Gigabit Ethernet SX
adapter

Check the following:

1. Verify that the adapter is seated firmly in the slot.

2. Try a different Gigabit Ethernet SX adapter.

Diagnostics pass but the
connection fails

Ensure the network cable is securely attached

Another adapter stopped
working after you installed
the Gigabit Ethernet SX
Adapter

Check the following:

1. Verify that the cable is connected to the Gigabit Ethernet SX Adapter and not to

another adapter.

2. Check for a resource conflict.

3. Ensure both adapters are seated firmly in the slot.

4. Check all cables.

The adapter stopped working
without apparent cause

Check the following:

1. Reseat the adapter.

2. Reinstall the drivers. The network driver files might be damaged or deleted.

3. Try a different Gigabit Ethernet SX Adapter.

100

Model 326 User’s Reference

Содержание totalstorage 326

















































































































































































































































Результаты поиска

Содержание totalstorage 326

Отзывы:

Похожие инструкции для totalstorage 326

Бренды по названию

Популярные бренды

IBM totalstorage 326, Справочник пользователя

Результаты поиска

Содержание totalstorage 326

Отзывы:

Похожие инструкции для totalstorage 326

Бренды по названию

Популярные бренды