IBM totalstorage 326 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 240

background image

Note:

Your version might be different from the one shown.

__________________________________

IBM ServeRAID BIOS

Copyright IBM Corp. 1994, 2001. All rights reserved.

BIOS Ver: 4.84.01

__________________________________

Controller 1 Slot 3, Logical drive=3, Other=0, Firmware=4.70.17, Status=OK

<< Press Ctrl+I to access the Mini-Configuration Program >>

Initializing ServeRAID Controller 1 in Slot 1.

Power-on self-test can take up to 59 Second(s) -- test Passed.

Drive configuration can take up to 6 Minute(s) 0 Second(s) -- test Passed.

If there is a POST Error message, the BIOS screen resembles the sample shown
below. Refer to “POST (ISPR) error procedures” on page 105 and correct the
problem. The characters

XXXX

indicate the POST (ISPR) error.

Note:

Your version might be different from the one shown.

__________________________________

IBM ServeRAID BIOS

Copyright IBM Corp. 1994, 2001. All rights reserved.

BIOS Ver: 4.84.01

__________________________________

Controller 1 Slot 3, Logical drive=3, Other=0, Firmware=4.70.17, Status=Failed

<< Press Ctrl+I to access the Mini-Configuration Program >>

Initializing ServeRAID Controller 1 in Slot 1.

Power-on self-test can take up to 59 Second(s) -- test Failed.

Controller is not responding properly - Run Diagnostics.

Error Code: XXXX-YY

The sample BIOS screen below shows configuration status and error information.

__________________________________

IBM ServeRAID BIOS

Copyright IBM Corp. 1994, 2001. All rights reserved.

BIOS Ver: 4.84.01

__________________________________

Controller 1 Slot 3, Logical drive=3, Other=0, Firmware=4.70.17, Status=OK

<< Press Ctrl+I to access the Mini-Configuration Program >>

__________________________________

Initializing ServeRAID Controller 1 in Slot 1.

Power-on self-test can take up to 59 Second(s) -- test Passed.

Drive configuration-can take up to 6 Minute(s) 0 Second(s) -- test Failed.

Controller POST and Config Error Codes: ISPR = EF10 BCS = 09 ECS = 20.

Following drives not responding (old state: new state: ch SID)

(RDY:EMP: 2:0)

The system has a configuration error due to above condition(s). Press: F4 - Retry

the command F5 - Update Controller configuration to exclude

NON-RESPONDING drives Warning: NON-RESPONDING drives will be set to

DDD, DHS, or EMP state F10 - Exit without change

Note: Do not

replace a ServeRAID-4 controller or a system board containing an

embedded ServeRAID-4 controller for ServeRAID problems unless replacing
the controller is listed in Table 16 on page 106.

104

Model 326 User’s Reference

«
...
114
115
116
117
118
...
»

Содержание totalstorage 326

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для totalstorage 326

Бренд: D-Link Страницы: 2

3CR860-95 - OfficeConnect Secure Router

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 26

Бренд: D-Link Страницы: 213

Бренд: Juniper Страницы: 7

Бренд: Daedalon Страницы: 6

Бренд: Renesas Страницы: 4

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

Бренд: Dahua Страницы: 113

Бренд: Xilinx Страницы: 27

Бренд: IFM Страницы: 12

Бренд: ADS Technologies Страницы: 1

Бренд: CSL Страницы: 24

Бренд: ATTO Technology Страницы: 2

Network Adapter AC AAP

Бренд: Extron electronics Страницы: 2

Бренд: C&H Technologies Страницы: 50

Pixel Processing Juggler

Бренд: 7th Sense Страницы: 148

Бренд: Pro-Nets Technology Corporation Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды