IBM totalstorage 326 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 240

background image

NVRAM Memory Test

Passed

Realtime Clock Test

Passed

Programmable Gate Array Test:

Passed

I2C Interface Test:

Passed

Main Application Checksum:

Passed

Boot Sector Checksum:

Passed

Onboard Ethernet Hardware Test:

Passed

PCI EEPROM Initialization Test:

Passed

5. When you finish viewing this information, press

Esc

to return to the main option

menu. Remove the CD, then restart the engine.

Testing SCSI adapters

The SCSI adapters are used for tape backup operations. You can test and
configure them during engine boot time by entering

Ctrl-A

when prompted. This

invokes the BIOS SCSI Select utility. Follow the on-screen directions when this
utility appears.

IBM 3534 Fibre Channel Hub Model 1RU

This section gives troubleshooting information for the IBM 3534 Fibre Channel Hub
Model 1RU.

Each hub port includes an LED indicator. If a problem has been detected with the
port, the LED indicators provide some indication of the type of problem. Faults and
problems are displayed with a yellow port indicator. The color and blink speed of
each port’s LED, as described in Table 18, indicates the status of each port.

Table 18. HUB front panel LED status indicators

Indicators

Status

No light showing

No light or signal carrier (no module, no
cable) for media interface LEDs.

Steady yellow

Receiving light or signal carrier, but attached
device not yet online.

Slow

1

yellow

Disabled (result of diagnostics or portDisable
command). Blinks every 2 seconds.

Fast

2

yellow

Error, fault with the port. Blinks every 1/2
second.

Steady green

Online (connected with device over cable)

Slow green

Online, but segmented (loopback cable or
incompatible switch). Blinks every 2 seconds.

Fast green

Internal loopback (diagnostic). Blinks every
1/2 second.

Flickering green

Online and frames are flowing through the
port.

Green and yellow

The port is bypassed.

Notes:

1.

Slow - blinks at 2 second intervals

2.

Fast - blinks at 1/2 second intervals

If a GBIC is not installed, no light shows on the LED. When a GBIC is installed and
a cable is connected to a properly functioning Fibre Channel device, the LED

Chapter 8. Troubleshooting

111

«
...
121
122
123
124
125
...
»

Содержание totalstorage 326

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для totalstorage 326

C50FSi - VB Network Camera

Бренд: Canon Страницы: 32

Бренд: Rabbit Страницы: 120

Бренд: Barco Страницы: 100

Бренд: National Instruments Страницы: 11

Бренд: Vonets Страницы: 8

Бренд: Hawking Страницы: 2

Бренд: Blackrock Microsystems Страницы: 27

Бренд: Justec Страницы: 61

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Бренд: Gemtek Systems Страницы: 51

Бренд: Kontron Страницы: 19

Бренд: RubyTech Страницы: 25

5200 Live Series EventCD

Бренд: MF DIGITAL Страницы: 21

J-Link-OB-STM32F072-128KB

Бренд: Segger Страницы: 18

CHEETAH ST34501FC

Бренд: Seagate Страницы: 68

Бренд: Planet Страницы: 2

COM Express conga-TC87

Бренд: Congatec Страницы: 114

Бренд: Kontron Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды