horsch LEEB PT 330 Скачать руководство пользователя страница 60

Страница: 60 / 203

Height adjustment of the steering column

Pull the unlocking lever on the right hand side

of the steering column forward and move the

steering column to the desired position. Then

shift the unlocking lever back again.

Pedal for steering column adjustment

Hold the steering wheel tightly before operat-

ing the pedal for steering column adjustment.

Move the steering column to the desired direc-

tion and release the pedal.

4.8.2 Travel direction selection

lever

After starting the engine and releasing the

parking brake you must pre-select the travel

direction.

This is accomplished by operating the travel

direction pre-selection lever.

Lever forward = Pre-selection for forward

travel

Lever backward = Pre-selection for backward

travel

After this pre-selection, the lever will automati-

cally return to middle position.

NOTE

Further notes on operation, see chapter "Engine

operation".

Содержание LEEB PT 330












































































































































































































Результаты поиска

Содержание LEEB PT 330

Отзывы:

Похожие инструкции для LEEB PT 330

Бренды по названию

Популярные бренды

horsch LEEB PT 330, Руководство по эксплуатации

Результаты поиска

Содержание LEEB PT 330

Отзывы:

Похожие инструкции для LEEB PT 330

Бренды по названию

Популярные бренды