Hitachi ZW 550-6 Скачать руководство пользователя страница 80

Страница: 80 / 438

OPERATOR'S STATION

1-16

Air Filter Restriction Indicator (Red)

If the air cleaner element becomes clogged,, the air

filter restriction indicator and the service indicator light.

Immediately stop the engine and inspect the air cleaner

element. Replace the element, if necessary.

NOTE: This indicator may unexpectedly light when the

coolant temperature gauge indicates the center or lower

position.

It turns off automatically when the coolant temperature

increases.

Preheat Indicator (Yellow)

The engine is being preheated as long as the preheat indicator

stays ON. When the preheat indicator goes OFF, engine

preheating is completed.

M4GB-01-023

M4GB-01-031

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды