Hitachi ZW 550-6 Скачать руководство пользователя страница 248

Страница: 248 / 438

OPERATING THE MACHINE

5-2

NOTE:

1. When applying lift arm control lever (1) in the "Raise"

position (A), the lever is moved (F) until the lift arm reaches

the position preset by the lift arm kickout. When the lift

arm moves the preset position, lift arm control lever (1)

automatically moves to the Neutral (N) position.

2. When applying bucket control lever (2) in the "Tilt" position

(D) after bucket dump operation, the lever is moved (G)

until the bucket reaches the position preset by the bucket

auto leveler. When the bucket reaches the preset position,

bucket control lever (2) automatically moves to the Neutral

(N) position.

3. When pushing down lift arm control lever (1) to the "Float"

position (C), the lift arm moves to the position preset by lift

arm auto-leveler system and is held in that position. When

the lift arm moves to the preset position, lift arm control

lever (1) automatically moves to the "Neutral" (N) position.

(Machine is equipped with the lift arm auto-leveler system)

NOTE: When operating the machine in Float (C) position,

first hold the lift arm at the float position; then further tilt

the lever to the Float position, and lower the lift arm on the

ground.

M4GB-01-073

115Z7-1-92-1

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды