Hitachi ZW 550-6 Скачать руководство пользователя страница 152

Страница: 152 / 438

OPERATOR'S STATION

1-88

Parking Brake Switch

WARNING:



To prevent accidents due to rolling away of the

machine, after parking the machine or before

leaving the machine, be sure to apply the parking

brake.



Never apply the parking brake while the machine

is moving except in an emergency.



Apply the parking brake only after the machine

has stopped.



Failure to do so may cause sudden deceleration

of the machine travel speed, possibly creating

a dangerous situation. Also, premature wear

and/or damage to the parking brake may result.

After the parking brake has been applied in an

emergency while moving the machine, have the

parking brake checked at your nearest Kawasaki

dealer.

When parking brake switch (1) is turned ON, the parking

brake is applied; parking brake indicator (2) will be shown.

Press the OFF side of parking brake switch (1) to release the

parking brake. Check that parking brake indicator (2) goes

OFF by pressing the switch firmly clicks.

NOTE:



The parking brake is released by hydraulic pressure only

when the engine is running.



To ensure safe operation, the machine should not travel

when the parking brake is applied, even if forward/

reverse switch (3) of the joystick steering is set to the

forward (F) or reverse (R) position.



To ensure safe operation, when the engine is stopped,

the parking brake is applied even if parking brake

switch (1) is in the OFF or released position.

Before restarting the engine, ensure the forward/reverse

switch (3) is in "neutral" position for safety.



The parking brake will be applied when the key is

turned OFF.

OFF

MNEC-01-058

115Z7B-4-4-1

115Z7B-1-81-1

MNEK-01-500

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды