Hitachi ZW 550-6 Скачать руководство пользователя страница 397

Страница: 397 / 438

MAINTENANCE

7-113

Check Windshield Washer Fluid Level
--- every 10 hours (daily)

IMPORTANT: Keep all dirt, dust and other foreign

materials out of the tank.

Check the fluid level. If necessary, add the fluid.

Check Play Amount in Joystick Steering

Movement
--- every 10 hours (daily)

Check that play (1) in joystick steering movement is correct.

In addition, check that the chassis steering stoppers come

in contact with the opposing chassis surface stopper when

the steering lever is fully moved and that the steering

cylinders operate normally.

1. Start the engine. Turn the parking brake switch ON.
2. Slightly lift the bucket above the ground. Place

control lever lock (2) in the lock

( ) position.

3. While running the engine at slow speed, slightly and

slowly move the joystick steering right and left.

Measure the beginning movement distance from the

center (neutral) position of steering lever until both

right and left steering cylinders start moving (check

the movement of the bucket and/or tires).

Appropriate play amount (1): 5~13 mm (0.2~0.5 in)

NOTE: If too much steering play is found or if the joystick

steering lever does not move smoothly, consult your

nearest authorized dealer for checking.

115Z7B-7-112-3

115Z7B-4-9-1

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды