Hitachi ZW 550-6 Скачать руководство пользователя страница 398

Страница: 398 / 438

MAINTENANCE

7-114

Check Accelerator Pedal Operation, and Exhaust

Gas Color and Noise
--- every 10 hours (daily)

WARNING: Move the forward/reverse switch (or

lever) to neutral. Apply the parking brake. After

resting the bucket level to the ground, block the

wheels.

While slowly stepping on accelerator pedal (1), check that

the engine speed smoothly increases. Then, while slowly

returning accelerator pedal (1), check that the engine

speed smoothly decreases.

Exhaust Gas Color and Noise:

DANGER: Exhaust inhalation hazard. Ventilate

the shop with fresh air when carrying out warming

up warm-up operation indoor. Failure to do so may

cause asphyxiation from exhaust gas, resulting in

death or severe injury.

IMPORTANT: This machine is equipped with the

engine that meets Interim Tier 4 emission

requirements. Never attempt to modify the inlet

and exhaust system.

Exhaust gas color is normally transparent or light blue.

Although exhaust gas color slightly becomes white

immediately after the engine is started or quickly

accelerated, this symptom is not abnormal. If the

exhaust gas color turns black, white, brown, or gray,

check the engine oil level and the fuel supply system for

any abnormality. In addition, check that no abnormal

noise is heard coming from the engine or muffler.

115Z7B-1-81-1

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды