Hitachi ZW 550-6 Скачать руководство пользователя страница 232

Страница: 232 / 438

MOVING THE MACHINE

4-6

Power Mode Selector

Pressing power mode selector switch (14) alternately

activates (ON) and deactivates (OFF) the power mode.

When the power mode is activated (ON), the indicator “ ”

appears on the monitor display.

The power mode is suited for heavy digging work

prioritizing work effectiveness. Under auto shifting

mode, the gear is shifted in regular RPM’s (min

-1

) and shift

mapping.

NOTE: When the power mode is OFF, the machine operates

prioritizing fuel consumption. Under auto shifting mode, the

gear is shifted in early timing.

Shift Change Delay Mode

When travel mode selector (13) is set in AUTO 1 or AUTO 2,

the shift up timing in 2nd range



3rd range is delayed.

Loading work can be easily done in 2nd range position.

Shift Up Delay

Forward

movement

: The gear shifts up when moving the

machine at high speed in 2nd range for 8

seconds or longer. The gear will not shift

while the lift arm is raising. The forward

shift up delay will operate only one time

when the bucket is in the operating

position. When the bucket is lower at

digging position, the shift delay always

operates.

Reverse

movement

: The gear shifts up when operating the

machine at high speed in 2nd range for

8 seconds or longer. The shift up delay

always operates.

NOTE:



This does not apply when the lockup clutch is used; shift up

timing from 2nd range to 2nd lock-up, or from 2nd lock-up

to 3rd range is not delayed.



Capability to activate or not activate the shift change

delay mode is selected via the transmission setting menu

on the monitor. Refer to page 1-59 for details.

OFF

MNEC-01-016

MNEC-01-024

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды