Hitachi ZW 550-6 Скачать руководство пользователя страница 143

Страница: 143 / 438

OPERATOR'S STATION

1-79

5. Press selector knob (2) to display Maintenance screen (7).

6. Rotate selector knob (2) to highlight a maintenance item

to be checked (8). (In the right example, Engine Oil is

selected.)

7. Press selector knob (2) to display the time remaining for

the selected maintenance item.

Resetting Data

To reset the remaining time data, rotate selector knob (2) to

highlight RESET (9), and then push selector knob (2).

The value of the remaining hours is reset to that of the

maintenance interval. The previous change date/hour is

updated with the current date and time.

Maintenance Interval Setting

To change the maintenance interval, rotate selector knob (2)

to highlight

(11), and then press selector knob (2).

The background color of Maintenance Interval (10) changes,

then turn selector knob (2) to adjust the time, and then

push selector knob (2) to enable the change.

MNHG-01-249EN

MNHG-01-250EN

MNHG-01-251EN

MNEC-01-006

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды