Hitachi ZW 550-6 Скачать руководство пользователя страница 244

Страница: 244 / 438

MOVING THE MACHINE

4-18

Parking

IMPORTANT: When parking the machine with cab

door and windows open, cab electrical components

may be damaged by bad weather. Always close

windows, roof vent and cab doors when parking

the machine.

1. Stop and park the machine on level surface. Lower

the bucket to the ground.

2. Turn parking brake switch (1) ON.

IMPORTANT: This machine is equipped with a

turbocharged engine. Therefore if the engine is

stopped without first cooling down at low RPM’s,

the lubricant on the turbocharger bearing and seal

surfaces may be dissipated due to the intense heat

present inside turbocharger, possibly damaging

the turbocharger.

3. Run the engine at low idle speed to cool the engine

for a few minutes.

NOTE: Do not idle for excessively long periods. Observe

local and federal engine idling regulations.

4. Turn key switch (2) to OFF position to stop the

engine. Remove the key from the switch.

5. Press lock ( ) side of control lever lock switch (3).

6. Push lock button (4) and lift armrest (5) to the fully

raised position.

7. Before leaving the machine, turn OFF the light switch,

close and lock all the windows, cab doors, and covers.

115Z7B-1-81-1

"Raised" position

115MNEC-07-01

115Z7B-1-10-3

Stop and Parking Position

115Z7B-BKT

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды