Hitachi ZW 550-6 Скачать руководство пользователя страница 285

Страница: 285 / 438

MAINTENANCE

7-1

Correct Maintenance and Inspection Procedures

Learn how to service your machine correctly. Follow the

correct maintenance and inspection procedures shown in this

manual.

Inspect machine daily before starting.



Check controls and instruments.



Check coolant, fuel, DEF and oil levels.



Check for leaks, kinked, frayed or damaged hoses and

lines.



Walk around machine checking general appearance,

noise, heat, etc.



Check for loose or missing parts.

If there is any problem with your machine, repair it before

operating or contact your authorized dealer for repairs.

IMPORTANT:



Use only recommended coolant, fuel, DEF, and

lubricants.



Be sure to use only genuine Hitachi parts. Failure to

do so may result in serious injury or death and/or

machine breakdown.



Failure to use recommended coolant, fuel, DEF,

lubricants, and genuine Hitachi parts will result in

loss of Hitachi product warranty.



Never adjust engine governor.

Never adjust hydraulic system relief valve.



Protect electrical parts from water and steam.



Never spray high pressure water or steam to

the transmission oil filler port, transmission air

breather, and vicinity of the axle air breather.



Never disassemble electrical components such as

main controller, sensors, etc.



Never adjust parts of engine fuel system.

Never adjust hydraulic equipment.



Using bad quality fuel, drainage agent, fuel

additives, gasoline, kerosene or alcohol refueled

or mixed with specified fuel may deteriorate

performance of fuel filters and cause surface

problems between moving parts at lubricated

contacts in the injector. It also affects the engine

and aftertreatment device parts, leading to

malfunction.



Use Hitachi genuine high performance filter.

SA-005

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды