Hitachi ZW 550-6 Скачать руководство пользователя страница 382

Страница: 382 / 438

MAINTENANCE

7-98

Removal and Installation of Tire

WARNING: A wheel and tire assembly is a very

heavy part so that removal and installation of a

tire is hazardous and difficult work. In addition,

a crane to lift a tire is required when removing or

installing the tire to the wheel. Consult your nearest

authorized dealer or a professional tire sales shop

for tire removal and installation work. When jacking

up the machine, observe the following points.



Select dry, solid and flat ground for a work site.



Work in a group of more than two persons. One

person to mainly do the work and others to work as

assistants and/or ensure safety.



Do not use the bucket to raise the front wheels.



Do not raise the machine off the ground higher

necessary.



When one axle is raised off the ground, block the tires

at the axle that is still in contact with the ground.



After the machine is raised off ground, be sure to

block the machine using rigid supports. If wooden

blocks are used for "cribbing" support, use only hard

wood blocks. Never use soft wood for support. Never

leave the machine to be supported only by jacks.



The rear wheels oscillate. Insert wooden blocks

between the axle and the chassis to stop oscillation.



When removing the wheel bolts, lift the wheel with

a crane so that the wheel bolt remaining at the top

position is removed lost.

Wheel bolt: 892 N·m (91 kgf·m, 658 lbf·ft)

Tire Wheel

WARNING: Use only reliable and professional

tire repair shops to do tire repair or replacements.

Only authorized professional repair shops should

be permitted to assemble and inflate tires. Rusty

rims that have been deeply corroded must not be

reused. Replace them with new rims.

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды