Hitachi ZW 550-6 Скачать руководство пользователя страница 236

Страница: 236 / 438

MOVING THE MACHINE

4-10

Secondary Steering (Option)

If the oil pressure in the steering system lowers, the

secondary steering system is activated so that steering

operation can be achieved. If the secondary steering

system is activated, the secondary steering indicator lights

and the buzzer sounds. Immediately park the machine in a

safe location. Then, contact your nearest authorized dealer.

The secondary steering can be used for 60 seconds.

IMPORTANT: The secondary steering system is

provided for an emergency use. If continuously

used for more than 60 seconds, damage to the

system may result.

Even though the machine is equipped with the secondary

steering system, if the steering function becomes

inoperable while moving machine, press secondary

steering check switch (1) on the right console to activate

the secondary steering system. Then, immediately park and

stop the machine in a safe location.

NOTE:



The secondary steering auto-check sound may be

heard for two seconds after starting the engine.



Before operating the machine, press secondary steering

check switch (1) to confirm that the secondary steering

pump operates normally.

MNEC-01-020

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды