Hitachi ZW 550-6 Скачать руководство пользователя страница 321

Страница: 321 / 438

MAINTENANCE

7-37

Change Axle Oil
--- every 2000 hours

WARNING: Be cautious about the following items.



Starting repair work immediately after operation

may cause burns. Wait for oil temperature to

lower.



Lock the front and rear chassis with the

articulation stopper (lock bar).

IMPORTANT: Do not use axle oils other than those

listed in the “Kind of Oils" - "Axle Oil”.

1. Park the machine and follow the procedures as

described on page 7-6 for preparation of inspection/

maintenance work.

NOTE: Adjust so that the "TOP" mark on the planetary

gear housing comes top. See the illustration on the next

page.

2. Install articulation stopper to the front and rear of

the chassis by following the procedures described on

page 7-8.

Change Differential Gear Oil

3. Clean the vicinity around drain plug (1) and the oil

drain plug hole.

4. Arrange a container of 120 liters (32 gallons) capacity

to receive the drain oil.

5.  Remove drain plug (1) to drain the oil.
6.  Securely tighten drain plug (1).
7.  Refill the specified amount of oil through oil level

plug (2) hole.

Front differential: 115 liters (30.4 gallons)

Rear differential: 115 liters (30.4 gallons)

IMPORTANT: It takes time for oil to fully lubricate the

overall front axle. After installing the plug, operate

the machine slowly for several minutes. Then, stop

the engine and check the axle for any oil leaks.

NOTE: It is recommended to drive the machine to

increase the axle oil temperature to 20 °C (68 °F) or higher

for smooth priming of oil. Check the oil level again and fill

up to the level plug (2).

8. Check the oil level. (Refer to Check Axle Oil Level.)

Front Axle

MNHE-07-024

115Z7B-7-35-3

Rear Axle

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды