Hitachi ZW 550-6 Скачать руководство пользователя страница 175

Страница: 175 / 438

OPERATOR'S STATION

1-111

Quick Power Switch

By pressing quick power switch (1) when the power mode

is OFF, the power mode is temporarily activated. (The

power mode indicator on the monitor shows symbol ( ).)

NOTE: The quick power switch is operable only in the

following cases.



An added push is needed during digging (tractive)

operation.



Need a little more acceleration or travel speed while

ascending on a slope.

When operating under low load or the forward/reverse

switch is in "Neutral" (N) position, the mode will not

change to power mode even if quick power mode switch is

pressed. The switch selection is ruled invalid.

Also, even if the machine is in the power mode, it is

canceled when the following conditions are met.



When operating load is decreased while digging.



When the quick power mode switch is pressed.



The forward/reverse switch is operated.



While driving in the auto-shift mode, the gear shifts

up to the selected gear stage.

Right Console Slide Lever

Adjust the position of the right console as follows.

1. While tilting lever (2) to the right, adjust the position

of the right console by sliding it back or forth.

Holding and moving armrest (3) maybe easier to

move the console.

Slide quantity: 90 mm (3.5 in)
2. After the adjustment, put back lever (2) to the

original position.

Fingertip Control Type

MNEC-01-043

Multi-Function Joystick Type

115Z7-1-107-2

115MNEC-01-043

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды