Hitachi ZW 550-6 Скачать руководство пользователя страница 68

Страница: 68 / 438

OPERATOR'S STATION

1-4



Refill DEF which meets JIS or ISO (International

Organization for Standardization). If improper

liquid (diesel oil, kerosene or gasoline) is refilled in

the DEF tank, fire or system failure may result.



Use only recommended engine oil. Using engine

oil other than the recommended may result in

malfunction of the aftertreatment device.



Contaminated fuel, incorrect fuel additives,

gasoline, kerosene or other incorrect fluids will

damage the fuel injection system and will lead

to engine malfunction, which is not covered by

warranty. Incorrect fuels will also damage the

aftertreatment device.

Use only clean Ultra Low Sulfur Diesel (ULSD) fuel

without additives that contain metal elements, oil

distillates or alcohol. These items will permanently

damage the aftertreatment device and are not

covered by warranty.



Do not modify the machine without authorization.

Never attempt to modify the air inlet and exhaust

parts such as the air duct, aftertreatment device

and the exhaust outlet. Also never attempt to

disassemble the aftertreatment device.



Avoid giving shocks on the aftertreatment

device by hitting elements with other objects or

dropping the device. Failure to do so may affect

the aftertreatment device, possibly damaging it or

lowering its performance.



It is normal to see white smoke appear during

regeneration. It is not caused by a malfunction.

Do not attempt to perform aftertreatment device

manual regeneration indoors in an area that is not

well ventilated or free from flammables.



Ammonia odor may occur during aftertreatment

device regeneration temporarily, but is not a

trouble.



Consult your authorized dealer for checking or

repairing the aftertreatment device.

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды