Hitachi ZW 550-6 Скачать руководство пользователя страница 312

Страница: 312 / 438

MAINTENANCE

7-28

115Z7B-7-28-3

Replace Engine Oil Filter
--- every 500 hours (each time when engine oil is

changed)

WARNING: Immediately after the machine has

been operated, all engine parts are hot. Wait for

the engine to cool before starting any maintenance

work. Failure to do so may cause severe burns.

1. Park the machine following the same procedures as

described on page 7-6 for preparation of inspection/

maintenance work.

IMPORTANT:



When replacing oil filters (1), make sure to replace

both of them at the same time.



When installing the oil filter, make sure that the

gasket is not caught at the rim. This could cause

oil leakage.



Any dirt on the cock or plug must be wiped off

before installing it.



Do not perform abrupt engine idling, which may

cause an engine failure.



After replacement, run the engine and confirm

that there is no oil leakage from the area around

the filter.

2. Clean around the oil filler cap so that foreign matter

does not enter. Remove the oil filler cap.

3. Place a container of approx. 60 L (16 gallons) capacity

under the oil pan and drain plug (2) to receive the

drain oil.

4. Remove oil pan drain plug (2) to drain the oil.

Retighten the plug.

NOTE: After all oil has been drained, inspect the cloth for

any debris such as small pieces of metal.

115Z7B-7-27-2

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды