Hitachi ZW 550-6 Скачать руководство пользователя страница 164

Страница: 164 / 438

OPERATOR'S STATION

1-100

Loading Multi-Function Joystick Lever (Option)

The multi-function joystick lever is used to operate the lift arm

and/or bucket.

Lever

Position

Bucket Operation

Float (Detent):

The lift arm free falls and can be moved as

loads are applied. The lever is held in this

position.

Lift Arm Lower

Hold:

The lift arm is stopped and held in that

position.

Lift Arm Raise

Detent:

The lift arm is held in the raise position.

Detent:

When the multi-function joystick lever is

moved from the bucket dump position to

the bucket tilt position, the multi-function

joystick lever is maintained in this position.

Bucket Tilt:

The bucket is tilted back, taking the

transportation position.

Hold:

The bucket is stopped and held in that

position.

Bucket Dump:

The bucket is tilted forward to dump the

bucket load.

M4GB-01-073

M4GB-01-074

MNEC-01-059

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды