Hitachi ZW 550-6 Скачать руководство пользователя страница 316

Страница: 316 / 438

MAINTENANCE

7-32

IMPORTANT: The machine is equipped with a

turbocharged engine. Cool down before stopping

the engine. Failure to do so may cause the lubricant

on the turbocharger bearing and seal surfaces

to be dissipated due to the intense heat present

inside the turbocharger, possibly damaging the

turbocharger.

4. Turn the key switch OFF to stop the engine. Leave the

machine untouched for 10 minutes.

5. Prepare a container of more than 120 L (32 gal)

capacity to receive the oil.

6. Remove drain plug (5) from the transmission bottom

to drain the oil. Dispose of the oil in accordance with

local regulations.

7. Loosen four bolts (6) with a 14 mm wrench.

8. Remove flange (7) together with the pipe and suction

strainer (8).

9. Remove set screw (9) using a 2.5 mm (0.1 in) hex

(allen) wrench from strainer (8).

10. Remove suction strainer (8) from flange (7).

Brush off any debris and clean with solvent.

NOTE: It is normal for a few fine particles to be on

strainer (8). Large pieces or a large quantity of particles

indicates a problem. Contact your authorized dealer if you

find excessive debris.

11. Reassemble and reinstall strainer (8), gasket (7) and

the drain plug with a new gasket (10).

12. Tighten four bolts (6).

Tightening torque: 53 N·m (5.4 kgf·m) (39 lbf·ft)

95Z7-7-32-2

115Z7B-7-32-1

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды