Hitachi ZW 550-6 Скачать руководство пользователя страница 26

Страница: 26 / 438

SAFETY

S-14

Drive Safely with Bucket Loaded



If the machine is operated incorrectly while driving with the

bucket loaded, the machine may turn over. Be sure to follow

all of the instructions indicated below.



When driving the machine on a job site with the bucket

loaded, hold the bucket as low as possible to keep the

machine balanced and to have good visibility.



Do not exceed the rated load capacity. Always operate

the machine within the rated load capacity.



Avoid fast starts, stops, and quick turns. Failure to do so

may result in personal injury and / or death.



Avoid rapid drive direction changes which could possibly

cause personal injury and / or death.

Drive on Snow Safely



Beware of the possibility of slipping or turning over the

machine when driving on frozen snow surfaces.



The machine may slip more easily than expected on

frozen snow surfaces even if the incline is small. Reduce

speed when driving. Avoid fast starts, stops and quick

turns.



Road shoulder and / or set-up utilities covered with snow

are difficult to locate. Be sure where they are before

removing snow.



Be sure to use tire chains when driving on snow.



Avoid applying the brake for quick stops on snow. If a

quick stop is required, lower the bucket to the ground.

SA-452

SA-400

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды