Hitachi ZW 550-6 Скачать руководство пользователя страница 309

Страница: 309 / 438

MAINTENANCE

7-25

B. Engine

Check Engine Oil Level
--- every 10 hours (machine parked on a level

surface before starting the engine)

IMPORTANT: Incorrect engine oil level may cause engine

trouble (The oil level should be between the upper

and lower marks on oil level gauge (1)).

If engine oil level is too high, lower the oil level to the

proper place before starting the engine.

Check oil level before starting the engine. If the engine has

been running, stop the engine and wait at least 30 minutes

before checking the oil level.

Pull out oil level gauge (1). Check for mixing of foreign matter

or contamination in the oil. Wipe oil level gauge (1) with cloth,

re-insert it into the pipe to the end, and then pull it out again.

The oil level should be between the [HIGH] and [LOW] marks

on oil level gauge (1).

If oil level is below the [LOW] mark, add the recommended

engine oil via oil filler (2).

If oil level exceeds the [HIGH] mark, loosen drain plug (3) to

drain excess oil.

: Plug (3): 78.5 N·m (8.0 kgf·m, 58 lbf·ft)

NOTE: Level the machine when adding oil or inspecting

oil level. When required to check oil level after operating

the machine, first stop the engine. Wait for more than 30

minutes. Then check oil level. (This means that the oil will

return to the oil pan, then oil level can be checked.) In case

the oil color changes, severe contamination, and/or mixing

of foreign matter may be seen, change the oil.

CAUTION: Do not spill oil while changing oil. Spilled

fuel, oil, and other flammables may cause fires.

95Z7B-7-25-1

95Z7-7-25-3

115Z7B-7-28-3

HIGH

Oil may be added

up to HIGH mark

Insufficient.

Oil must be added..

LOW

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды