Hitachi ZW 550-6 Скачать руководство пользователя страница 313 | Manualshive

Страница: 313 / 438

Hitachi ZW 550-6 Скачать руководство пользователя страница 313

MAINTENANCE

7-29

5. Remove element (3) by turning it counterclockwise

with the tool (oil filter wrench).

6. Apply a thin coat of clean engine oil to the gasket of

a new element.

IMPORTANT:



Do not reuse element (1).



When replacing oil filter elements, make sure to

replace both of them at the same time.

7. Install a new element.

Screw in the element until the gasket comes in

contact with the seal surface. Then tighten it by one

more turn using the tool (oil filter wrench).

8. Replace the other filter element in the same manner.

9. Confirm that the oil pan drain cock or plug is securely

tightened.

10. Remove the oil level gauge and carefully supply the

specified amount of engine oil from the oil filler.

11.  Install the oil level gauge and the filler cap.
12.  Start the engine 5 minutes after refueling.
13.  While running the engine at low idle, check the oil

filter, drain cock, and sealing surfaces for any oil

leakage.

14. Stop the engine. About 20 minutes later, recheck the

oil level. If necessary, add oil.

Gasket

Element

MNHE-07-068

Filter Body

3

«
...
311
312
313
314
315
...
»

Содержание ZW 550-6























































































































































































































































































































































































































































Отзывы:

Нет отзывов