Hitachi ZW 550-6 Скачать руководство пользователя страница 33

Страница: 33 / 438

SAFETY

S-21

Park Machine Safely

To avoid accidents:



Park the machine on a firm, level surface.



Lower bucket to the ground.



Put the forward / reverse lever (switch) in neutral, and

turn the parking brake switch (lever) ON (parking brake)

position.



Run the engine at low idle speed without load for 3

minutes.



Turn key switch to OFF to stop engine.



Remove the key from the key switch.



Turn the control lever lock switch to the lock ( ) position.



Close windows, roof vent, and cab door.



Lock all access doors and compartments.

Store Attachments Safely



Stored attachments such as buckets, hydraulic hammers,

and blades can fall and cause serious injury or death.



Securely store attachments and implements to prevent

falling. Keep children and bystanders away from storage

areas.

SA-034

SA-456

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды