Hitachi ZW 550-6 Скачать руководство пользователя страница 227

Страница: 227 / 438

MOVING THE MACHINE

4-1

Driving the Machine

Correct operation will result in extending the service life of

each part and component as well as saving fuel and oil.

Always be sure to safely and efficiently operate the

machine while paying attention to the following points.

IMPORTANT: The engine must be started and ready

for driving correctly by referring to the previous

section “OPERATING THE ENGINE”.

Precautions for Starting to Move

1. Perform a thorough walk-around inspection.

Conduct correct start-up procedure.

2. After raising the lift arm, set the lift arms and bucket

in the operating position.

3. Before driving on public roads, set the machine to the

driving position as illustrated to the right.

4. Be sure to press lock ( ) side of control lever lock

switch (1) so that the linkage will not move even if

the control levers are accidentally moved.

Position

A: 545 mm (21.5 in)

115Z7B-4-1-1

Multi-Function Joystick Type

MNEC-01-043

Fingertip Control Type

115Z7B-1-9-4

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды