Hitachi ZW 550-6 Скачать руководство пользователя страница 233

Страница: 233 / 438

MOVING THE MACHINE

4-7

Parking Brake Switch

WARNING:



To prevent accidents due to running away of the

machine, after parking the machine or before

leaving the machine, be sure to apply the parking

brake.



Never apply the parking brake switch (1) while

moving the machine except in an emergency.

Premature wear and/or damage to the parking

brake may result. After the parking brake has

been applied in an emergency while moving the

machine, have the parking brake checked at your

nearest authorized dealer.

1. Press the OFF side of parking brake switch (1) to

release the parking brake. Check that parking brake

indicator (2) goes OFF by pressing the switch firmly

twice.

Press the ON side of parking brake switch (1) to apply

the parking brake.

Operate the parking brake after stopping the

machine on level ground.

NOTE: While running the engine, when the parking

brake is applied with forward/reverse switch (3) in neutral,

parking brake indicator (2) comes ON.

2. While running the engine, when the parking brake

is applied with forward/reverse switch (3) in either

the forward (F) or reverse (R) position, parking brake

indicator (2) comes ON, and the alarm buzzer sounds.

F-N-R display (4) of the monitor display indicates "N"

not "R". The display will not indicate "F" and "R" until

the parking brake is released.

3. To ensure safe operation, when the engine is

stopped, the parking brake is applied even if parking

brake switch (1) is in the OFF position.

In this case even after the engine is restarted, the

parking brake will not be released. After starting the

engine, push the ON position of parking brake switch

(1) once. Then, push the OFF position parking brake

switch (1) to release the parking brake.

OFF

MNEC-01-058

115Z7B-1-81-1

MNEK-01-500

115Z7B-4-4-1

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды