Hitachi ZW 550-6 Скачать руководство пользователя страница 169

Страница: 169 / 438

OPERATOR'S STATION

1-105

115MNEC-07-01

Power Mode Selector Switch

Two operation modes are available and can be selected

by power mode selector switch (1) depending on the

applications.

Each time the switch is pressed, the power mode is

activated (ON) and deactivated (OFF) alternately.

Power

mode

(ON)

: The power mode is suitable for

heavy digging work prioritizing work

effectiveness.

Under auto shifting mode, the gear is

shifted in regular engine RPM's (min

-1

) and

shift mapping.

Power

mode

(OFF)

: When the power mode is turned OFF, the

machine operates putting more emphasis

on lowering fuel consumption.

Under auto shifting mode, the gear is

shifted with lower engine RPM's (min

-1

)

and shift mapping.

When the power mode is activated, the symbol ( ) is

displayed on the power mode indicator of the monitor

screen.

2nd/3rd Speed Limit Switch (Option)

A three-position switch (1) is provided to enable the

operator to limit the maximum gear to 2nd or 3rd range

while driving in auto shift mode. This is used exclusively

with the optional joystick steering without the steering

wheel/shift lever.

MNEC-01-016

95Z7B-1-112-1

Limit to 2nd Speed

Limit to 3rd Speed

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды