Hitachi ZW 550-6 Скачать руководство пользователя страница 39

Страница: 39 / 438

SAFETY

S-27

Prevent Parts from Flying



Travel reduction gears are under pressure.



As pieces may fly off, be sure to keep body and face away

from AIR RELEASE PLUG to avoid injury.



GEAR OIL is hot. Wait for GEAR OIL to cool, then gradually

loosen AIR RELEASE PLUG to release pressure.

Prevent Burns

Hot spraying fluids:



After operation, engine coolant is hot and under pressure.

Hot water or steam is contained in the engine, radiator and

heater lines.

Skin contact with escaping hot water or steam can cause

severe burns.



Avoid possible injury from hot spraying water. DO NOT

remove the radiator cap until the engine is cool. When

opening, turn the cap slowly to the stop. Allow all

pressure to be released before removing the cap.



The hydraulic oil tank is pressurized. Again, be sure to

release all pressure before removing the cap.

Hot fluids and surfaces:



Engine oil, gear oil and hydraulic oil also become hot during

operation.

The engine, hoses, lines and other parts become hot as well.



Wait for the oil and components to cool before starting

any maintenance or inspection work.

SA-039

SA-225

SA-344

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды