Hitachi ZW 550-6 Скачать руководство пользователя страница 240

Страница: 240 / 438

MOVING THE MACHINE

4-14

Precautions for Driving on Slopes

WARNING:



Never allow the machine to descend a slope with

the forward/reverse switch (or lever) in neutral

(N). This will not only cause the excessive engine

revolutions to malfunction but also cause other

engine and machine troubles.



When descending a slope, use normal resistance

to travel as exerted by the engine through

the drive train. Apply the brakes only when

absolutely required. If the brake is continuously

used while descending a slope, the brake

temperature will increase, possibly decreasing

braking performance.

If overheating of the brake system is noticed,

immediately park the machine in a safe location.

Restart and operate the machine only after the

brake system is sufficiently cooled.



When descending a slope, do not operate the

machine at a speed faster than the maximum

travel speed. Failure to do so may damage the

machine and/or a serious accident may result.

When steering on a slope, lower the loader front to

increase the machine stability. Do not steer on a steep

slope since this may cause the machine to turn over.

When descending a slope, descend in a low drive range

with engine resistance applied.

Do not operate the machine at a speed faster than the

maximum travel speed.

In case the engine stalls on a slope, immediately step

on the service brake pedal, lower the loader arms to

the ground and stop the machine. The parking brake

is automatically applied when the engine is stopped

regardless of the position of the parking brake switch.

Before restarting engine, return the forward/reverse switch

to neutral (N) and turn the parking brake switch ON.



Before descending a slope, confirm that the service

and parking brake systems work normally.



In case the hydraulic oil and lubricant temperatures

are low, the machine gradability may decrease. Before

climbing a steep slope, warm up the machine.

Содержание ZW 550-6























































































































































































































































































































































































































































Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды

Hitachi ZW 550-6, Руководство оператора

Результаты поиска

Содержание ZW 550-6

Отзывы:

Похожие инструкции для ZW 550-6

Бренды по названию

Популярные бренды