GSi EVO-50 Скачать руководство пользователя страница 95

Страница: 95 / 222

4. Install the cover hinge weldments (55) to the outside of the right outer door cover angle (53) using

four 5/16" x 1" MS screws (9), 5/16" flat washers (18) and 5/16" flange nuts (28).

5. Install the door latch mounting bracket (54) to the outside of the left outer door cover angle (53)

using two 5/16" x 1" MS screws (9) and 5/16" flange nuts (28).

NOTE:

Align the door latch mounting bracket (54) to the center of the outer door cover angle (53)
and install with the bolt heads on the inside.

Figure 7-20

Installing the door latch mounting bracket and outer cover hinge weldments

5/16" x 1" MS screw with sealing washer
(S-10633)

Outer door cover angle (NCWT0744)

5/16" flat washer (S-845)

Door latch mounting bracket (WD-6286)

5/16" flange nut (S-10268)

Cover hinge weldment (NCWT0165)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 95 / 222

Результаты поиска

Содержание EVO-50

Отзывы: