GSi EVO-50 Скачать руководство пользователя страница 165

Страница: 165 / 222

Attaching the A-Frame to the Center Collar

The upper portion of the A-frame assembly must be installed to the center collar, so that it supports the
center collar and the main roof structure.

Before You Begin

Make sure the center collar is assembled and secured to the center support pole. See

Center Collar

Placement, page 162

for details. Determine the correct location of each A-frame. For more information,

see

About Temperature Cable Brackets and A-Frame Assemblies, page 139

. Read and understand the

safe and proper lifting procedures needed to install the A-frames. For more information, see

Guidelines

for Assembling and Lifting the A-Frame Rafter Sections, page 163

1. Carefully lift the A-frame assembly (133) into position and align with the proper holes on the center

collar (45).

2. Install 1/2" x 1-3/4" flange bolts (5) and 1/2" flange nuts (17) to secure the A-frame assembly (133)

to the center collar (45).

3. Before continuing with the remaining A-frame assemblies, secure the A-frame assembly (133) to the

eave bracket. See

Attaching the A-Frame to the Eave Bracket, page 166

4. Tighten all the hardware to the recommended torque specifications. See

Bolt Torque Specifications,

page 26

Figure 8-25

Attaching the A-frame to the center collar

1/2" x 1-3/4" flange bolt (S-10252)

Outer center collar (CTR-2224-BS)

1/2" flange nut (S-10253)

133

A-frame assembly

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

165

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 165 / 222

Результаты поиска

Содержание EVO-50

Отзывы: