GSi EVO-50 Скачать руководство пользователя страница 187

Страница: 187 / 222

Chapter 8: Roof Assembly

Installing the Flashing Lock

The flashing lock will need to be installed to secure the roof flashing and the top panel.

1. Position the flashing lock (125) under the roof flashing (118), aligning with the holes in the top

panel (121) from the underside of the roof.

NOTE:

Ensure the roof flashing (118) is inserted between the top panel (121) and the flashing
lock (125).

2. Install 3/8" x 1" flange bolts (3) and 3/8" flange nuts (15) to secure the top panel (121) with the

flashing lock (125).

3. Repeat the procedure to install the remaining flashing locks (125).

4. Tighten all the hardware to the recommended torque specifications. See

Bolt Torque Specifications,

page 26

Figure 8-45

Installing the flashing lock

3/8" x 1" flange bolt with sealing washer (S-7487)

121

Top panel (CTR-1585)

3/8" flange nut (S-9426)

125

Flashing lock (CTR-1588)

118

Roof flashing (CTR-2120)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

187

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 187 / 222

Результаты поиска

Содержание EVO-50

Отзывы: