GSi EVO-50 Скачать руководство пользователя страница 86

Страница: 86 / 222

4. Position the door stiffeners (61) under the base stiffener (60) on top of the outer door frame

weldment (31) and install using 3/4" x 5" HHTB bolts (4), 3/4" flat washers (16), 3/4" square washers
(17) and 3/4" hex nuts (25).

NOTE:

Make sure to place the upper cover (37) between the base stiffener (60) and the outer door
frame weldment (31) before installing the HHTB bolts (4).

5. Repeat steps 2 and 3 to attach the door stiffeners (61) to the stiffener support weldment (62).

Figure 7-12

Installing the door stiffeners - 3 post

3/4" x 5" HHTB bolt (S-7324)

Upper cover (NCWT0761)

3/4" flat washer (S-866)

Base stiffener

3/4" square washer (HT-635-BS)

Door stiffener (NCWT0482-BS)

3/4" hex nut (S-240)

Stiffener support weldment (NCWT0481-BS)

Outer door frame weldment (NCWT0756)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 86 / 222

Результаты поиска

Содержание EVO-50

Отзывы: