manualshive.com logo in svg

GSi EVO-50, Руководство по монтажу, Страница: 82 / 222

Поделиться
Скачать
GSi EVO-50 Скачать руководство пользователя страница 82

Chapter 7: Door Assemblies

3. Install the seal weldments (36) to the top and bottom of the door frame weldments (31 and 33) using

3/8" x 2" flange bolts (3), special washers (14) and 3/8" hex nuts (24).

NOTE:

Refer to note in

Installing the Door Weldment, page 77

for details on the specific order in

which these parts must be assembled. (The seal weldments must be installed into the
sidewall before the frames and jamb plate weldments.)

NOTE:

The upper cover (37) will be installed later along with the installation of the door and base
stiffeners.

NOTE:

Make sure to install the flange bolts (3) with bolt head and washers (14) on the outside of the
door frame weldments (31 and 33).

Figure 7-8

Installing the seal weldments - 3 post

3

3/8" x 2" flange bolt with sealing washer (S-10165)

31 Outer door frame weldment (NCWT0756)

14 Special washer (S-10102)

33 Inner door frame weldment (NCWT0751-BS)

24 3/8" hex nut (S-456)

36 Seal weldment (NCTW0759)

82

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Отзывы:

Нет отзывов