GSi EVO-50 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 222

GSi EVO-50 Скачать руководство пользователя страница 123

Chapter 7: Door Assemblies

6. Install the top and bottom outer door latches (56 and 57) to the door latch mounting bracket (54)

using 5/16" x 3/4" carriage bolts (12), latch bushing (44) and 5/16" flange nuts (28).

NOTE:

Make sure the holes in the outer door latches (56 and 57) align with the holes in the door
latch mounting bracket (54) to allow the door to be locked.

7. Install the latch bar (58) to the top and bottom outer door latches (56 and 57) using 5/16" x 1/2"

flange bolts (13) and 5/16" flange nuts (28).

Figure 7-47

Installing the door latches and latch bar

12

5/16" x 3/4" carriage bolt (S-6076)

54

Door latch mounting bracket (WD-6286)

13

5/16" x 1/2" flange bolt (S-10579)

56

Top outer door latch (WD-6279)

28

5/16" flange nut (S-10268)

57

Bottom outer door latch (WD-6278)

44

Latch bushing (WD-6040)

58

Latch bar (WD-6039)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

123

«
...
121
122
123
124
125
...
»

Содержание EVO-50































































































































































































































Отзывы:

Нет отзывов