GSi EVO-50 Скачать руководство пользователя страница 167

Страница: 167 / 222

Chapter 8: Roof Assembly

Assembling the Roof Panel Clips

The roof panel clips provide support to the roof panels at the peak and are installed nearest to the center
collar.

Before You Begin

Make sure all the rafter assemblies are installed and secured to both the center collar and eave bracket.

What You Should Know

Roof panel clips are installed between the two rafter assemblies.

1. Attach one roof panel clip (113) to each side of the left side roof rafter (30) using two 1/2" x 1-3/4"

flange bolts (5) and 1/2" flange nuts (17).

2. Attach the next roof panel clip (113) to the right hand side of the right side roof rafter (30) along with

the roof panel clip (113) on the left using 1/2" x 1-3/4" flange bolts (5) and 1/2" flange nuts (17).

NOTE:

Make sure that the roof panel holes in the roof panel clip (113) are at the top and the notch in
the roof panel clip (113) is facing the right side roof rafter (30).

3. Continue to install the remaining roof panel clips (113) to each side of the roof rafters (30).

4. Tighten all the hardware to the recommended torque specifications only after the roof panels are

installed. See

Bolt Torque Specifications, page 26

Figure 8-27

Installing the roof panel clip to the rafter assembly

1/2" x 1-3/4" flange bolt (S-10252)

Upper roof rafter (CTR-2179)

1/2" flange nut (S-10253)

113

Roof panel clip (CTR-2191)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

167

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 167 / 222

Результаты поиска

Содержание EVO-50

Отзывы: