GSi EVO-50 Скачать руководство пользователя страница 108

Страница: 108 / 222

Chapter 7: Door Assemblies

Installing the Seal Weldment

1. Install the seal weldment (36) and the upper cover (37) to the top of the door frame weldments (31

and 33) as shown using 3/8" x 2" flange bolts (3), special washers (14) and 3/8" hex nuts (24).

NOTE:

Install the upper cover (37) to the two holes in the middle of outer door frame weldment (31).

NOTE:

Refer to note in

Installing the Door Weldment, page 104

for details on the specific order in

which these parts must be assembled. (The seal weldments must be installed into the
sidewall before the frames and jamb plate weldments.)

2. Install the seal weldment (36) to the bottom of the door frame weldments (31 and 33) using

3/8" x 2" flange bolts (3), special washers (14) and 3/8" hex nuts (24).

NOTE:

Make sure to install the flange bolts (3) with bolt head and washers (14) on the outside of the
door frame weldments (31 and 33).

Figure 7-33

Installing the seal weldments - 2 post

3/8" x 2" flange bolt with sealing washer (S-10165)

Inner door frame weldment (NCWT0763-BS)

14 Special washer (S-10102)

Seal weldment (NCTW0775)

24 3/8" hex nut (S-456)

Upper cover (NCWT0748)

31 Outer door frame weldment (NCWT0769)

108

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 108 / 222

Результаты поиска

Содержание EVO-50

Отзывы: