GSi EVO-50 Скачать руководство пользователя страница 83

Страница: 83 / 222

Chapter 7: Door Assemblies

Installing the Door Frames to the Sidewall

1. Position the jamb plate weldments (32) to the inside of the sidewall with outer door frame weldment

(31) to the outside of the bin.

2. Place the corrugated sealing strip (69) between the outer and inner edges of the sidewall to jamb

plate weldment (32) connection. Apply rope caulk (68) around the corrugated sealing strip (69).

3. Also, apply rope caulk (68) between the sidewall to seal weldment (36) at the top and bottom of the

door frame weldments.

NOTE:

Refer to note in

Installing the Door Weldment, page 77

for details on the specific order in

which these parts must be assembled. (The seal weldments must be installed into the
sidewall before the frames and jamb plate weldments.)

Figure 7-9

Caulking the door frame

Outer door frame weldment (NCWT0738) (2-post)

Seal weldment (NCTW0745) (2-post)

Outer door frame weldment (NCWT0756) (3-post)

Seal weldment (NCTW0759) (3-post)

Jamb plate weldment (NCWT0736-BS) (2-post)

Rope caulk

Jamb plate weldment (NCWT0754-BS) (3-post)

Inner door frame weldment (NCWT0732-BS) (2-post)

Corrugated sealing strip

Inner door frame weldment (NCWT0751-BS) (3-post)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 83 / 222

Результаты поиска

Содержание EVO-50

Отзывы: