GSi EVO-50 Скачать руководство пользователя страница 166

Страница: 166 / 222

Chapter 8: Roof Assembly

Attaching the A-Frame to the Eave Bracket

The bottom end of the rafters in the A-frame must be installed to the eave brackets.

1. Lower the A-frame assembly (133) along the side of the eave bracket (23) and align with the proper

holes.

2. Install 1/2" x 1-3/4" flange bolts (5) and 1/2" flange nuts (17) to secure the rafter on one side on the

A-frame assembly (133) to the eave bracket (23).

3. Repeat this procedure for the other side of the A-frame assembly (133).

4. Tighten all the hardware to the recommended torque specifications. See

Bolt Torque Specifications,

page 26

Figure 8-26

Attaching the A-frame to the eave bracket

1/2" x 1-3/4" flange bolt (S-10252)

Eave bracket (CTR-2174-BS)

1/2" flange nut (S-10253)

133

A-frame rafter assembly

After You Finish

Continue to install the next A-frame assembly to the center collar and then to the eave brackets until all
the A-frame assemblies are installed.

166

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 166 / 222

Результаты поиска

Содержание EVO-50

Отзывы: