GSi EVO-50 Скачать руководство пользователя страница 75

Страница: 75 / 222

Door Assemblies

Topics Covered in this Chapter

▪

General Information

▪

Door Assembly Instructions (NCWT0731 and NCWT0750)

▪

Door Assembly Instructions (NCWT0762 and NCWT0778)

General Information

Two Ring Doors for Various Bin Heights

The two ring door used for each bin depends upon the number of rings. Refer to the below table to identify
the door used with each bin height.

Table 7-1

Two ring door information

S.No

Bin Diameter

Bin Rings

Stiffener Post

Door Assembly

90'

25 Rings and Shorter

2-Post

NCWT0731

3-Post

NCWT0750

26 Rings and Taller

2-Post

NCWT0762

3-Post

NCWT0778

1. The commercial two ring door is installed in the bottom two rings.

2. The door should normally be placed in line with the conveyor. An intermediate discharge well should

be located near the wall to clear the grain from the area of the access door (as with any access
door).

3. The door should be located between the two stiffeners.

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 75 / 222

Результаты поиска

Содержание EVO-50

Отзывы: