GSi EVO-50 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 222

GSi EVO-50 Скачать руководство пользователя страница 142

Chapter 8: Roof Assembly

Assembling the Temperature Cable Bracket

The temperature cable brackets are installed to the roof rafters and support the temperature cables.

Before You Begin

Determine the correct location of the temperature cable brackets within the A-frame Assembly. See

Temperature Cable Brackets and A-Frame Assemblies, page 139

.

What You Should Know

The A-frame assembly consists of two roof rafters, purlin clips, purlins and possibly diagonal bracing. The
temperature cable brackets should be installed when the A-frames are assembled.

NOTE:

The temperature cable bracket must be installed at specific locations, see

About Temperature

Cable Brackets and A-Frame Assemblies, page 139

.

1. Attach the temperature cable support weldment (42) and temperature cable mount plate (43) to the

bottom flange of the roof rafter (128) using six 1/2" x 2-1/4" HHCS bolts (6) and 1/2" hex nuts (14).

2. After all the purlins and diagonal bracing are installed to the A-frame, tighten all the hardware to the

recommended torque specifications. See

Bolt Torque Specifications, page 26

Figure 8-9

Installing a temperature cable bracket to the A-frame

6

1/2" x 2-1/4" HHCS bolts (S-7894)

43

Temperature cable mount plate (CRP-6156-BS)

14

1/2" hex nut (S-3729)

128

Roof rafter

42

Temperature cable support weldment
(CRP-6164-BS)

142

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

«
...
140
141
142
143
144
...
»

Содержание EVO-50































































































































































































































Отзывы:

Нет отзывов