manualshive.com logo in svg

GSi EVO-50, Руководство по монтажу, Страница: 32 / 222

Поделиться
Скачать
GSi EVO-50 Скачать руководство пользователя страница 32

Chapter 3: Hardware Requirements

Nut (S-10785)

An S-10785 is a M10 flange nut that is pre-assembled with a conical HDPE sealing washer.

Nut (S-10785) is used in the following locations:

• Used to connect all laminated sidewall connections.

5

0.43" (1.1 cm)

6

Grade 10.9

Nut (S-9426)

An S-9426 is a 3/8" flange nut.

Nut (S-9426) is used in the following locations:

• Use to connect the C-clamps to stiffener or wind ring brackets in

wind rings.

• Use to connect the eave bracket to the inside stiffener.
• Use to connect the lower stand-off brackets to the outer center

collar.

• Use to connect the top panel to the center collar brackets.
• Use to connect the upper stand-off brackets to the top plate and

outer center collar.

• Use to connect the flashing lock to the top panel.

5

0.347" (0.88 cm)

7

Grade 5

Nut (S-9281)

An S-9281 is a 7/16" hex nut.

Nut (S-9281) is used in the following locations:

• Use in wind ring splice and over pipe connections.

5

0.385" (0.977 cm )

7

Grade 5

32

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Отзывы:

Нет отзывов