GSi EVO-50 Скачать руководство пользователя страница 52

Страница: 52 / 222

Chapter 5: Installing the Base Angle

Installing the Anchor Bolt Washer

Anchor bolt washers help to cover the oversized hole in the base plate.

Before You Begin

Make sure the anchor bolts are secured and the base plates are installed.

1. Place a square plate washer (16) onto the anchor bolt (15).

NOTE:

The square washer (provided) must be placed between the base boot plate (17) and flat
washer (2).

2. Place a flat washer (2) above the square washer (16) and secure with a nut (4).

3. Tighten to the recommended torque specification, see

Bolt Torque Specifications, page 26

Figure 5-3

Installing the anchor bolt washer

Flat washer

Square anchor plate washer

Anchor nut

Base boot

Anchor bolt

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 52 / 222

Результаты поиска

Содержание EVO-50

Отзывы: