GSi EVO-50 Скачать руководство пользователя страница 199

Страница: 199 / 222

Chapter 9: Bin Accessories

Assembling the Roof Exhauster

Assembly of the roof exhauster is done prior to installing onto the roof.

1. Apply a strip of tube caulk (81) along the mating surface of the roof exhauster hood (80) and the

exhauster mounting plate (75).

2. Position the roof exhauster hood (80) over the exhauster mounting plate (75) and align all the holes.

3. Install 5/16" x 1" flange bolts (1) and 5/16" flange nuts (10) to secure the roof exhauster hood (80) to

the exhauster mounting plate (75).

Figure 9-8

Assembling the roof exhauster hood to the mounting plate

5/16" x 1" flange bolt with sealing washer (S-10260)

Roof exhauster hood

5/16" flange nut (S-3611)

Tube caulk

Exhauster mounting plate (CTR-1302)

PNEG-5490D-2X

90' Diameter EVO-50 Beam 2X Bin

199

Содержание EVO-50































































































































































































































Результаты поиска

Содержание EVO-50

Отзывы:

GSi EVO-50, Руководство по монтажу, Страница: 199 / 222

Результаты поиска

Содержание EVO-50

Отзывы: