Graco Horizon Fluid Management Systems Скачать руководство пользователя страница 7

Страница: 7 / 108

308607

Pre-installation Checklist

Pre-installation Steps

Reference

7. Repeat the following steps for each control module:

a. For each solenoid attached to the control module, assign one port num-

ber, from 1 to 6. Record the port number and whether it is an air or fluid
solenoid on the Floor Plan.

NOTE:

Air and fluid solenoids can be inter-

mixed on the Horizon ports.

b. For each meter attached to the control module, assign one port number,

from 7 to 12. Record the port number on the Floor Plan.

NOTE:

than one dispense point (reel, oil bar, hose, etc.) can share a meter.

CAUTION: Record all the information carefully as it must be accu-

rately entered during software setup.

Floor Plan

8. Record the system data from the Floor Plan to the corresponding Pre-instal-

lation Forms. The completed forms will ease system setup by placing the

information in the order the software will request the input. To ease software

setup, keep the items in numerical order.

Pre-installation Forms

Form #1:

User Name, PIN Number, and Access Level

Form #2:

Control Module and Fluid: Names and Numbers

Form #3:

Dispense Area Names and Numbers

Form #4:

Connection Assignments

Form #5:

Meter Calibration Chart

Form #6:

Warranty Registration and Checkout Form

Floor Plan and Forms
1--6; see examples of
forms on pages 86--96

9. Make sure the following tools are available for the system installation:

Drill, drill bit, and anchors to mount the control modules and keypad
brackets on the walls or beams

Wire cutter

Wire stripper (wire gauge ranges between 18 and 22 AWG)

Small, slotted screwdriver

VOM (volt-ohmmeter) or multimeter to check cable continuity, input
voltage, etc.

10. You are now ready to install the system. See the

Installation Checklist

page 8.

Содержание Horizon Fluid Management Systems













































































































Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды

Graco Horizon Fluid Management Systems, Инструкция по эксплуатации

Результаты поиска

Содержание Horizon Fluid Management Systems

Отзывы:

Похожие инструкции для Horizon Fluid Management Systems

Бренды по названию

Популярные бренды